China Fabric Factory Fabric News Main technical indicators of rapier belt products

Main technical indicators of rapier belt products



Main technical indicators of rapier belt products 1. Comparison of rapier belt product models and loom models (Table 14-1) Table 14-1 Comparison table of rapier belt models and app…

Main technical indicators of rapier belt products

1. Comparison of rapier belt product models and loom models (Table 14-1) Table 14-1 Comparison table of rapier belt models and applicable rapier loom models

2. Appearance Requirements (1) The product surface should be flat and clean, without debonding, delamination, wrinkles, pits and other defects. (2) The surface roughness of the bottom surface of the rapier belt and both sides of the wide width is Ral.6, the surface roughness around the perforation is Ra3.2, and the surface of the wear-resistant layer is not allowed to have traces of mechanical finishing (non-metal finishing surface roughness grade is based on the metal surface The roughness grade is reduced by one level, that is: non-metallic Rat.16 is equivalent to metal Ra3.2). (3) Straightness and warpage ≤3mm. 3. Product technical performance The product technical performance is shown in Table 14-2.

IV. Shape and position tolerances (1) The straightness tolerance on both sides of the bandwidth is 0.20/1000mm. (2) The symmetry tolerance of the center of the perforation relative to the center line of the sword belt is 0.20mm. 5. Main matching dimensions (Table 14-3)

6. Service life The average service life of the rapier belt is more than 5.8×107 times. 7. Inspection rules 1. Batch grouping rules Rapier belt products are inspected in batches. Products using the same raw materials, the same formula, the same process, and produced on the same day are designated as a batch. 2. Inspection items The inspection items for rapier belts are as specified in Table 14-4.

3. Production inspection The sampling inspection method should be formulated in accordance with the requirements of GB/T2828-1987 that the general inspection level is IT and the qualified quality level (AQL) is 4.0. 4. Factory inspection Before each batch of rapier belt products leaves the factory, they should be inspected according to the factory inspection items and sampling quantities specified in Table 14-4. If one of the inspection results does not meet the requirements, it will be judged as a substandard product and the product will be scrapped. deal with. 5. Type inspection Rapier belt products should undergo type inspection under the following circumstances: (1) During normal production, it should be conducted at least once per quarter. (2) When there are major changes in raw materials, processes, structures, etc. (3) When the model has been out of production for more than 1 year and resumes production. (4) When products have batch quality problems. (5) When the customer requests inspection. (6) When the national quality supervision department puts forward inspection requirements. Each type inspection shall include all items of mechanical properties (including tensile properties and bending properties), physical properties and chemical properties specified in Table 14-2. When any test data is unqualified, double samples should be taken from the same batch of products for re-inspection. If the re-inspection test data is qualified, the batch of products is deemed to be qualified; if the re-inspection still fails, the batch of products will be scrapped; at the same time, measures should be taken to address the reasons for the failure to avoid this happening again. 8. Labeling, storage, packaging and transportation Each rapier belt should be printed with the trademark and batch number identification on the fixed part of the belt body. Also, rapier straps should be stored indoors under natural conditions. The storage period is 5 years. Rapier belt products must be packed and shipped in closed wooden boxes or containers made of other materials that are sufficient to withstand transportation and handling, or packaged in the manner agreed by the customer to avoid damage during transportation. During transportation, it should be protected from being soaked in snow, exposed to heat, and deformed under heavy pressure.
AAAVBBCNVM,N. KJO

Extendedreading:https://www.alltextile.cn/product/product-76-822.html
Extendedreading:
Extendedreading:
Extendedreading:
Extendedreading:
Extendedreading:
Extendedreading:
ExtendedReading:
Extendedreading:
Extendedread

This article is from the Internet, does not represent 【www.factory-fabric.com】 position, reproduced please specify the source.https://www.factory-fabric.com/archives/33062

Author: clsrich

 
TOP
Home
News
Product
Application
Search